Marvel Industries Refrigerator 6SBAR User Manual

Marvel 6SBAR Beverage Center  
Installation  
Operation &  
Maintenance  
Instructions  
Part of AGA Foodservice Group  
 
Grounding Method: This product is factory  
equipped with a power supply cord that has a three-  
pronged grounded plug. It must be plugged into a  
mating grounding type receptacle in accordance with  
the National Electrical Code and applicable local  
codes and ordinances (see figure 1). If the circuit  
does not have a grounding type receptacle, it is the  
responsibility and obligation of the customer to  
exchange the existing receptacle in accordance with  
the National Electrical Code and applicable local  
codes and ordinances. The third ground prong  
should not, under any circumstances, be cut or  
removed. All U.L. listed refrigerated products are  
equipped with this type of plug.  
To start your appliance, use a screwdriver to turn the  
control clockwise to the middle thermostat setting  
(see figure 2). Once the beverage center is loaded,  
allow at least 48 hours for the unit to stabilize before  
making any adjustments to the initial setting.  
Insert Wine Bottles: The wine rack roll-out shelf  
holds eight bottles. See figure 3 for typical wine  
bottle orientation.  
Rear Bottles (Necks Facing Front)  
Front Bottles (Necks Facing Rear)  
How to Operate Your  
Figure 3  
Refrigerated Beverage Center  
Note: Wine rack can be located at the middle or  
bottom part of the cabinet interior. For red wines,  
place wine shelf at bottom shelf position in the  
cabinet. Then put a glass shelf in the next higher  
position. For white and sparkling wines, put the  
wine shelf on the middle shelf position in the cab-  
inet. Place the remaining shelves as desired.  
Also, there is a fixed, wooden, bottle cradle in the  
bottom, step section of the cabinet. Six bottles of  
wine may be stored there.  
Set the Control: The total available temperature  
range of the unit is from 39°F to the high sixties,  
depending on the thermostat setting and location of  
the cabinet. The middle range on the control is from  
the mid-forties to the mid-fifties depending on ambient  
Control Knob  
temperature and location of  
the cabinet. The tempera-  
ture can be lowered or  
raised by turning the control  
clockwise or counterclock-  
wise, respectively. As with  
any refrigeration product,  
(At bottom right  
section of grille)  
Loading Tips and  
Suggestions for Wine Rack  
Figure 2  
there is a slight temperature variance at different loca-  
tions within the cabinet. For example, the coolest area  
will be in the rear of the middle of the cabinet.  
Commodities on the top shelf will be 3° to 8° warmer.  
This section and the bottom cabinet step section are  
the warmest areas. Items in the front of the middle  
shelves will be 1° to 4° warmer than the rear of the  
shelves. Position your wine inventory accordingly on  
your wine shelf.  
The wooden, bottom bottle cradle may be removed for  
storing "jug" wines. Just remove the two screws that  
secure the cradle to the cabinet floor.  
You can store magnum bottles and other large bottles  
on any of the shelves (except for the top shelf) by  
removing the shelf directly above them or placing the  
shelf at a position allowing for proper clearance.  
The glass shelves and fixed position wire rack are for  
general beverage storage, such as beer and soft  
drinks. Opened wine bottles and tall beverage con-  
tainers may be stored on the glass shelf closest to the  
cabinet top. Just lift the hinged section of the fixed  
position upper wire rack to provide clearance for the  
bottles and/or containers to stand upright.  
Commodities on the top rack directly under the light will  
be exposed to a slightly higher temperature when the  
light is on. REMEMBER TO TURN OFF THE LIGHT  
WHEN IT IS NO LONGER NEEDED.  
Keep wines that you plan to use for everyday drinking  
and entertaining on the front half of the racks where  
labels are completely visible. Place wines for aging or  
longer term storing in rear.  
Do not pull out upper glass shelf when tall bottles are placed  
upright through the opening in the hinged wire shelf. Doing  
so may cause the tall, upright bottles to fall backwards.  
2
 
5
Using the /16” hex-head driver, resecure the two  
How to Clean and  
Maintain Your beverage center  
hex-head screws back into their original positions to  
fasten the light tube housing assembly to the top of  
the cabinet.  
Condenser: The condenser tubing inside the cabinet  
does not require frequent cleaning; however, satis-  
factory cooling depends on adequate ventilation over  
the coils. Be sure that nothing obstructs the required  
air flow openings in front of the cabinet. At least once  
or twice a year brush or vacuum lint and dirt from the  
condenser for efficient performance by unscrewing  
the grille on the bottom front of the cabinet.  
Re-use the original two screws to secure the light tube  
housing in place. Plug the beverage center into the  
electrical socket. Check to see if the light tubes oper-  
ate properly. Your light tube’s replacement is complete.  
The light tubes are not covered by your guarantee. A  
replacement light tube housing can be obtained from  
your service provider or from Marvel Industries.  
Cabinet: The painted cabinet can be washed with  
mild soap and water and thoroughly rinsed with clear  
water. Never use abrasive scouring powders.  
What to do in  
the Event of a Power Failure  
Interior: Wash interior compartment with mild soap  
and water. Do not use an abrasive powder, solvent,  
polish cleaner or undiluted detergent.  
Most power failures are corrected within two hours  
and will not affect the unit’s temperature providing you  
minimize the number of door openings while the  
power is off. A gradual rise in temperature should not  
have any adverse effect on your wine if power is out  
for a longer period. If it is extremely hot, you may  
want to move your wines to the coolest location you  
can find until power is restored.  
Glass Door: Use a glass cleaner or mild soap and  
water and soft cloth to clean the glass door model.  
Do not use any abrasive powders.  
Door Gasket: The vinyl gasket may be cleaned with  
mild soap and water, a baking soda solution or a mild  
scouring powder.  
Light Tube Replacement: WARNING! DISCONNECT  
THE POWER CORD BEFORE ATTEMPTING LIGHT  
TUBE HOUSING ASSEMBLY REPLACEMENT.  
Failure to do so may result in an electrical shock that  
could severely injure you.  
Appliance Features  
Adjustable Temperature Control: Please see “how  
to Operate Your Refrigerated Beverage Center” on  
page two.  
This product uses one, 6 watt light tube to illuminate  
the interior of the beverage center. The light tube is a  
very reliable electrical component, but should it not  
function properly, please call the dealer you pur-  
chased your beverage center from for a replacement  
light tube housing assembly. Use only an original  
equipment light tube housing assembly from your  
dealer or manufacturer.  
Interior Light and Switch: The interior light makes it  
easy to view the contents of your beverage center.  
When the switch is in the  
“OFF” position, the light  
will come on when the  
door is opened. When  
the switch is pushed such  
5
Using a /16” hex-head driver, remove the two hex-  
head screws holding the old light tube housing  
assembly in place. Disconnect the electrical plug  
from the cabinet’s electrical receptacle and discard  
the old light tube housing assembly. Reconnect the  
electrical plug of the new light tube housing assem-  
bly to the cabinet’s electrical receptacle. Make sure  
it is secure and fully inserted.  
that the “red” portion of  
the rocker is showing, the  
switch is in the “on” position and the interior light will  
stay on continuously. Remember to turn the off the light  
when it is no longer needed.  
3
 
Roll-out Shelves: The roll-out shelves may be pulled  
out approximately 14 inches to facilitate product loading  
and retrieval. Do not lean on or press down heavily on  
the shelves, doing so may damage the shelves or their  
content. Pull out shelves gently to minimize any possible  
item shifting. To maintain stability, avoid pulling out more  
than one shelf at any time.  
Before Calling for Service  
Before calling for service, check the trouble shooting  
table on this page. This table lists possible problems  
that you can remedy without difficulty to avoid an unnec-  
essary service call.  
If you do need service, contact your dealer or the manu-  
facturer. In any correspondence, refer to the model  
number and serial number of your unit which is located  
on the lower front cabinet flange. Retain you proof of  
purchase. You may want to record these numbers in the  
space provided on this page. Follow the procedure out-  
lined on page 5.  
The roll-out shelves are equipped with a removable  
center section that allows you to customize the stor-  
age capability of your beverage center. Your unit is  
shipped with two glass shelves,one wine rack, one  
wooden bottle cradle, and one fixed wire shelf. For  
added versatility, additional center sections are avail-  
able. Please contact dealer or see Marvel’s website at  
Possible  
Causes/Solutions  
Problem  
•Interior needs cleaning  
Odor in cabinet  
Noisy operation  
•Cabinet not level  
•Weak floor  
•Cabinet not level  
•Weak floor  
Cabinet vibrates  
•Tube burned out  
•No power at outlet  
Cabinet light not working  
Appliance will not run  
Temperature control turned  
to “OFF”  
•Line cord not plugged in  
•No power at electrical outlet  
•House fuse blown  
•Prolonged door openings  
•Control set too cold  
•Condenser needs cleaning  
Appliance runs too long  
Moisture collects inside  
Single Bottle Racks: Because bottles are not stacked  
on top of each other, you can easily view and access  
your inventory without disturbing other bottles.  
Too many door openings  
•Prolonged door openings  
•Hot, humid weather  
increases condensation  
•Hot, humid weather  
increases condensation. As  
humidity decreases,  
Moisture collects on outside  
surface  
moisture will disappear.  
•Control improperly set.  
•Control improperly set  
•Faulty thermometer  
•Relocate thermometer to  
center of cabinet and  
recheck  
Interior too hot/too cold  
4
 
If You Do Need Service  
How to Obtain Service  
In the event that you do need service, be sure to report the  
model number, serial number and proof of purchase to your  
service representative. Model number and serial number  
are found on the serial plate which is located on the lower  
front cabinet flange. For your convenience you may want to  
record the following information for your records.  
Your refrigerated beverage center requires little service  
because the best and most up to date materials, equip-  
ment and quality methods are employed throughout the  
manufacturing process.  
If trouble occurs during normal operation, first check the  
troubleshooting chart on page 4 to see if any of these  
simple steps may correct the problem. If service  
becomes necessary:  
Date of purchase  
Dealer’s Name  
Dealer’s Address  
Dealer’s City  
Contact the dealer where your appliance was purchased  
or the manufacturer for the name of your nearest  
authorized service representative. The service represen-  
tatives will have full authority tom make any repair  
deemed necessary.  
If you are in an area where there is no service repre-  
sentative, write or call the manufacturer directly. We  
will make recommendations as to the proper proce-  
dure for correction. Service work and replacement -  
parts, if required, will be provided as covered by your  
limited warranty.  
Dealer’s State  
Zip  
Appliance Serial Number  
Model Number  
IT IS IMPORTANT THAT YOU SEND IN YOUR WAR-  
RANTY RECORD CARD IMMEDIATELY AFTER TAKING  
DELIVERY OF YOUR REFRIGERATION APPLIANCE.  
Date Warranty Card Sent  
(Must be within 10 Days of Purchase)  
Every new refrigeration appliance that leaves the factory  
contains this Owner's Guide in a safe place for conven-  
ient reference.  
Normal Responsibilities  
of the Owner Include  
Under Counter Beverage Center Specifications  
Dimensions W x H x D (in.)  
Weight  
237/  
8
x 34 x 241/  
4
All freight charges.  
145 lbs.  
39-69°F  
115V  
Damage sustained in transit (see page 1)  
Mileage charge(s) for service calls.  
Proper installation.  
Temperature  
Power Supply  
supplied with a 15 amp plug  
Alterations to original equipment.  
Removal or installation of additional equipment.  
5
 
THE WARRANTIES SET FORTH HEREIN ARE THE  
ONLY WARRANTIES EXTENDED BY MARVEL INDUS-  
TRIES. ANY IMPLIED WARRANTIES, INCLUDING THE  
IMPLIED WARRANTY OF MERCHANTABILITY, ARE  
LIMITED TO THE DURATION OF THESE EXPRESS  
WARRANTIES. IN NO EVENT SHALL MARVEL INDUS-  
TRIES BE LIABLE FOR ANY CONSEQUENTIAL OR  
INCIDENTAL DAMAGES OR EXPENSES RESULTING  
FROM BREACH OF THESE OR ANY OTHER WAR-  
RANTIES, WHETHER EXPRESSED OR IMPLIED.  
Some states do not allow the exclusion or limitation of  
consequential damages or limitations on how long an  
implied warranty lasts, so the above exclusion or limita-  
tion may not apply to you. This warranty gives you spe-  
cific legal rights, and you may also have other rights  
which may vary from state to state.  
Marvel Household Refrigeration  
Products Limited Warranty  
Entire Product - Limited One Year Parts and Labor  
Warranty. MARVEL warrants that it will supply all neces-  
sary parts and labor to repair or replace in the end  
user's home or office, any component which proves to  
be defective in materials or workmanship, subject to the  
condition and exclusions stated below, for period of one  
year from date of purchase by the end user.  
Additional Second Through Fifth Year Limited Parts Only  
Warranty. During the four years following expiration of  
the One Year Limited Warranty, MARVEL will supply  
replacement parts for the hermetically sealed refrigera-  
tion system which consists of the compressor, condens-  
er, drier, connecting tubing and the evaporator that are  
proven to be defective due to workmanship or materials  
subject to the conditions and exclusions below.  
No person, firm or corporation is authorized to make  
any other warranty or assume any other obligation for  
MARVEL INDUSTRIES. These warranties apply only to  
products used in any of the fifty states of the United  
States and the District of Columbia.  
The above warranties do not cover:  
- Shipping costs of replacement parts or returned  
defective parts.  
- Customer education or instructions on how to use  
the refrigerator/freezer.  
To obtain performance of this warranty, report any  
defects to:  
- Any content loss due to product failure. - Removal  
or installation.  
MARVEL INDUSTRIES  
P.O. Box 997  
Richmond, Indiana 47375-0997  
Phone: 765-962-2521  
Nor do the above warranties cover failure of this product  
or its components due to:  
IN NO EVENT SHALL THE COMPANY BE LIABLE FOR  
INCIDENTAL OR CONSEQUENTIAL DAMAGES  
INCLUDING, BUT NOT LIMITED TO, CONTENT LOSS.  
- Transportation or subsequent damages.  
- Use commercially or use other than normal house-  
hold or office.  
- Improper installation, misuse, abuse, accident or  
alteration, use on wiring not confirming to electrical  
codes, low voltage, failure to provide necessary  
maintenance, or other unreasonable use.  
- Parts or service not supplied or designated by MARVEL.  
Some states do not allow limitations on length of time  
implied warranty may last, so the above limitations may  
not apply to you.  
This warranty gives you specific legal rights. You may  
also have other rights which very from state to state.  
The above warranties also do not apply if:  
- The original Bill of Sale, deliver date or serial num-  
ber cannot be verified.  
- Defective parts are not returned for inspection if so  
requested by MARVEL.  
- The refrigeration equipment is not in the posses-  
sion of the original end use purchaser.  
Help prevent tragedies  
Each year children die because they climb inside a  
discarded refrigeration product, get trapped inside  
and suffocate. Take precautions to prevent such  
tragedies by removing the door, taping or chaining it  
shut before discarding.  
6
 
W W W . M A R V E L I N D U S T R I E S . C O M  
Phone: (765) 962-2521 Fax: (765) 962-2493  
Marvel Industries  
Part of AGA Foodservice Group  
233 Industrial Parkway  
P.O. Box 997  
Richmond, IN 47375-0997  
41008927 Rev A  
 

KWC Plumbing Product 10031003 User Manual
Lenovo Computer Monitor 3024HC1 User Manual
LG Electronics Cell Phone TM510 User Manual
Lightolier Indoor Furnishings T7032 User Manual
Linksys Switch SLM2008 User Manual
Mace Digital Camera CAM 5 User Manual
Magnavox DVD VCR Combo cmwR20v6 User Manual
Makita Power Screwdriver 68OODBV User Manual
Martin Audio Portable Speaker Blackline H3+ User Manual
Melissa Automobile Parts 646 056 User Manual