comply with emission limits.
INTRODUCTION
The instrument is a portable digital thermometer that
measures external thermocouples of type K, J, R, S, T, E,
N. The thermocouples types comply with the N.I.S.T. –
ITS 90 standard reference temperature/voltage tables.
The thermometer features a dual thermocouple input, an
adjustable T/C offset.
Changes or modifications not expressly approved
the party responsible for compliance could void
user‘s authority to operate the equipment.
OMEGAnet On-Line Service
omega.com
Internet e-mail
HH806W
WIRELESS MULTILOGGER THERMOMETER
Servicing North America:
WIRELESS NOTE
Wireless receiver must keep a distance of at least 30cm
from the meter and meter to meter distance must be at
least 20cm.
M4556/0907
U.S.A:
One Omega Drive, Box 4047
Stamford, CT 06907-0047
INSTRUCTION
SHEET
Shop online at: omega.com e-mail: [email protected]
For latest product manuals: omegamanual.info
ISO 9001 Tel: (203) 359-1660
FAX: (203) 359-7700
SAFETY INFORMATION
Certified e-mail: [email protected]
Canada:
976 Bergar
Laval (Quebec) H7L 5A1, Canada
WARNING
To avoid electrical shock, do not use this instrument
when working voltages at the measurement surface
over 24V AC or DC.
SPECIFICATIONS
Tel: (514) 856-6928
FAX: (514) 856-6886
e-mail: [email protected]
ELECTRICAL
For immediate technical or application assistance:
Measurement Range:
U.S.A
and
Sales Service: 1-800-826-6342/1-800-TC-OMEGA®
WARNING
To avoid damage or burns, do not make temperature
measurement in microwave ovens.
K-TYPE (0.1°) -200°C to 1372°C (-328°F to 2501°F)
J-TYPE (0.1°) -210°C to 1200°C (-346°F to 2192°F)
T-TYPE (0.1°) -200°C to 400°C (-328°F to 752°F)
E-TYPE (0.1°) -210°C to 1000°C (-346°F to 1832°F)
Customer Service: 1-800-622-2378/1-800-622-BEST®
Canada:
Mexico:
En Espan ol: (001) 203-359-7803
e-mail: [email protected]
R-TYPE (1°)
S-TYPE (1°)
0°C to 1767°C (32°F to 3212°F)
0°C to 1767°C ( 32°F to 3212°F)
CAUTION
Repeated sharp flexing can break the thermocouple
leads. To prolong lead life, avoid sharp bends in the
leads, especially near the connector.
N-TYPE (0.1°) -50°C to 1300°C ( -58°F to 2372°F)
*Based on the ITS-90 temperature standard.
According to temperature standard ITS-90.
Accuracy:
Servicing Europe:
Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands
Tel: +31 (0)20 3472121 FAX: +31 (0)20 6434643
Toll Free in Benelux: 0800 0993344
e-mail: [email protected]
K/J/T/E-TYPE
FEDERAL COMMUNICATIONS
COMMISSION
±(0.05% rdg + 0.3°C) on -50°C to 1372°C
±(0.05% rdg + 0.7°C) on -50°C to -210°C
±(0.05% rdg + 0.6°F) on -58°F to 2501°F
±(0.05% rdg + 1.4°F) on -58°F to -346°F
N-TYPE
±(0.05% rdg + 0.8°C) on -50°C to 0°C
±(0.05% rdg + 0.4°C) on 0°C to 1300°C
±(0.05% rdg + 1.6°F) on -58°F to 32°F
±(0.05% rdg + 0.8°F) on 32°F to 2372°F
R/S-TYPE
±(0.05% rdg + 2°C) on 0°C to 1767°C
±(0.05% rdg + 4°F) on 32°F to 3212°F
Temperature Coefficient:
0.1 times the applicable accuracy specification per °C
from 0°C to 18°C and 28°C to 50°C (32°F to 64°F and
82°F to122°F).
Czech
Frystatska 184, 733 01 Karviná, Czech Republic
Republic: Tel: +420 (0)59 6311899 FAX: +420 (0)59 6311114
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two condi-
tions:(1) this device may not cause harmful interfer-
ence, and (2) this device must accept any interference
received, including interference that may cause unde-
sired operation.
France:
11, rue Jacques Cartier, 78280 Guyancourt, France
Tel: +33 (0)1 61 37 2900 FAX: +33 (0)1 30 57 5427
Toll Free in France: 0800 466 342
e-mail: [email protected]
Germany/ Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
Austria:
Tel: + 49 (0)7056 9398-0 FAX: +49 (0)7056 9398-29
Toll Free in Germany: 0800 639 7678
e-mail: [email protected]
NOTE
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection. This equipment gener-
ates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the in-
structions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation If
this equipment does cause harmful interference to ra-
dio or television reception, which can be determined
by turning the equipment off and on, the user is en-
couraged to try to correct the interference by one or
more of the following measures:
United
One Omega Drive, River Bend Technology Centre
Kingdom: Northbank, Irlam, Manchester
ISO 9002 M44 5BD United Kingdom
Certified Tel: +44 (0)161 777 6611 FAX: +44 (0)161 777 6622
Toll Free in United Kingdom: 0800-488-488
e-mail: [email protected]
Input Protection:
24V dc or 24V ac rms maximum input voltage on any
combination of input pins.
Reading Rate: 2.5 time per second.
It is the policy of OMEGA Engineering, Inc. to comply with all
worldwide safety and EMC/EMI regulations that apply. OMEGA
is constantly pursuing certification of its products to the
European New Approach Directives. OMEGA will add the CE
mark to every appropriate device upon certification.
The information contained in this document is believed to be
correct, but OMEGA accepts no liability for any errors it
contains, and reserves the right to alter specifications without
notice.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
These products are not designed for use in, and
should not be used for, human applications.
- Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV tech-
nician for help.
Shielded interface cables must be used in order to
this button will change the thermocouple type for
displays.
Press the number buttons printed in white on the
overlay to change the offset of the thermocouple. The
resolution of the setup is 0.1°. Press the “-” button to
set a negative value. Press the overlay “ENTER” but-
ton to confirm. MAX: ±1999.9 °C/°F.
(12) “[TIME]” Button (System time setting)
To set the system time, press the [TIME] button in the
setup mode. The third display should show the current
date and time with the year flashing. Enter the new
value from left to right in the following format
YY:MM:DD and HH:MM:SS. Press the number but-
tons printed in white on the overlay to set the system
date and time. Press the “ENTER” button to confirm.
Exit this function by pressing ESC button.
Where Do I Find Everything I Need for
Process Measurement
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in
materials and workmanship for period of from date of pur-
chase. OMEGA’s WARRANTY adds an additional one (1) month grace
period to the normal to cover handling and
shipping time. This ensures that OMEGA’s customers receive maximum
coverage on each product.
a
and Control?
(11) “TYPE” Button (Second display)
Press this button to change the type of thermocouple in
the second display (K/J/T/E/R/S/N). If the inputs of
the main and second display are the same, then press-
ing this button will change the thermocouple type for
both displays.
OMEGA…Of Course!
Shop online at omega.com
If the unit malfunctions, it must be returned to the factory for evaluation.
OMEGA’s Customer Service Department will issue an Authorized Return
(AR) number immediately upon phone or written request. Upon examination
by OMEGA, if the unit is found to be defective, it will be repaired or replaced
at no charge. OMEGA’s WARRANTY does not apply to defects resulting
from any action of the purchaser, including but not limited to mishandling,
improper interfacing, operation outside of design limits, improper repair, or
unauthorized modification. This WARRANTY is VOID if the unit shows
evidence of having been tampered with or shows evidence of having been
damaged as a result of excessive corrosion; or current, heat, moisture or
vibration; improper specification; misapplication; misuse or other operating
conditions outside of OMEGA’s control. Components which wear is not
warranted, include but are not limited to contact points, fuses, and triacs.
TEMPERATURE
Thermocouple, RTD & Thermistor Probes,
Connectors, Panels & Assemblies
Wire: Thermocouple, RTD & Thermistor
Calibrators & Ice Point References
Recorders, Controllers & Process Monitors
Infrared Pyrometers
4. SETUP MODE
The following functions can only be use in the setup
mode.
(2)
PRESSURE, STRAIN AND FORCE
Transducers & Strain Gages
Load Cells & Pressure Gages
Displacement Transducers
Press the LIMITS button to enter the Hi/Lo limit setup
function. The words “LIMIT” and “Hi” will be flash
on the LCD along with the previous value for the Hi
limit. Enter the new Hi limit value using the number
keys printed in white on the overlay. The resolution of
Hi/Lo limit setup is 1 count . The “-“ button (same
button as the ESC) can be used to enter negative val-
ues. Press the “ENTER” button to confirm the new
limit. You will then be prompted to enter a new Lo
limit value. Enter the new value and then press enter
to finish setup of limits.
WARNING
Instrumentation & Accessories
To avoid possible electrical shock, disconnect the
thermocouple connectors from the thermometer before
removing the cover.
FLOW/LEVEL
Rotameters, Gas Mass Flowmeters & Flow
Computers
Air Velocity Indicators
Turbine/Paddlewheel Systems
Totalizers & Batch Controllers
Battery Replacement
1. Power is supplied by 4pcs 1.5V (AAA SIZE) UM-4
R03.
2. The “ ” appears on the LCD display when replace-
ment is needed. To replace battery remove screw from
back of meter and lift off the battery cover.
3. Remove the battery from battery contacts and replace.
4. When not in use for long periods remove battery.
5. Do not store in locations with high temperatures, or
high humidity.
(3) “[INVT]”
(Interval time setting)
pH/CONDUCTIVITY
pH Electrodes, Testers & Accessories
Benchtop/Laboratory Meters
Controllers, Calibrators, Simulators & Pumps
Industrial pH & Conductivity Equipment
To setup the time interval for the log function, press
the [INVT] button. The indicator “INV” will blink on
the top-right of the LCD and the previous interval is
displayed. Press the number buttons printed in white
on the overlay to change the time interval. Setting is
from left to right of the following format
(HH:MM:SS). Press the overlay “ENTER” button to
confirm. To exit this function, press the ESC button.
HH: interval Hour (0~23)
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor
shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used
in or with any nuclear installation or activity; or (2) in medical applications or
used on humans. Should any Product(s) be used in or with any nuclear
installation or activity, medical application, used on humans, or misused in
any way, OMEGA assumes no responsibility as set forth in our basic
DATA ACQUISITION
WARRANTY
/
DISCLAIMER language, and, additionally, purchaser will
Data Acquisition & Engineering Software
Communications-Based Acquisition Systems
Plug-in Cards for Apple, IBM & Compatibles
Datalogging Systems
indemnify OMEGA and hold OMEGA harmless from any liability or damage
whatsoever arising out of the use of the Product(s) in such a manner.
Cleaning
Periodically wipe the case with a damp cloth and deter-
gent, do not use abrasives or solvents.
Recorders, Printers & Plotters
MM: interval Minute (0~59)
SS: interval Second (0~59)
MAX: 23:59:59
MIN: 00:00:01
Direct all warranty and repair requests / inquiries to the OMEGA Customer
Service Department. BEFORE RETURNING ANY PRODUCT(S) TO
OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR)
NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN
ORDER TO AVOID PROCESSING DELAYS). The assigned AR number
should then be marked on the outside of the return package and on any
correspondence.
HEATERS
Heating Cable
Cartridge & Strip Heaters
Immersion & Band Heaters
Flexible Heaters
*Software Operation manual is in the Software disk.
(8) “APO” Button (Auto power off time setting,
min. 1 minute)
The purchaser is responsible for shipping charges, freight, insurance and
proper packaging to prevent breakage in transit.
Laboratory Heaters
Use this function to change the time for the auto power
off (APO) function. Press the APO button in setup
mode, and the indicator “APO” and the current time
will flash on the LCD. The default time for APO is 5
minutes. Press the number button printed in white on
the overlay to set the APO time. Press the overlay
“ENTER” button to confirm. To exit this function
without changing the setting, press the ESC button.
MAX: 19999 minutes
ENVIRONMENTAL
FOR
RETURNS,
FOR
please have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number under
which the product was
REPAIRS, consult OMEGA for
current repair charges. Have the
following information available
BEFORE contacting OMEGA:
1. Purchase Order number to cover
the COST of the repair,
MONITORING AND CONTROL
Metering & Control Instrumentation
Refractometers
Pumps & Tubing
PURCHASED,
Air, Soil & Water Monitors
Industrial Water & Wastewater Treatment
pH, Conductivity & Dissolved Oxygen
Instruments
2. Model and serial number of the
product under warranty, and
3. Repair instructions and/or specific
problems relative to the product.
2. Model and serial number of the
product, and
3. Repair instructions and/or specific
problems relative to the product.
MIN: 0001 minutes
(9)“[OFS]” Button (Thermocouple offset ad-
just)
When the main display input is T1 and a thermocouple
is connected, the instrument can adjust the offset of the
thermocouple. The same can be done for T2 when on
the main display. In the setup mode, press this button
to enter the thermocouple Offset Setup Function (OFS)
and the indicator CAL should be displayed on the top-
right of the LCD and the current setting is also shown.
OMEGA’s policy is to make running changes, not model changes, whenever
an improvement is possible. This affords our customers the latest in tech-
nology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2007 OMEGA ENGINEERING, INC. All rights reserved. This
document may not be copied, photocopied, reproduced, translated, or
reduced to any electronic medium or machine-readable form, in whole or in
part, without the prior written consent of OMEGA ENGINEERING, INC.
Made in Taiwan
|