Accton Technology EN2216 2 User Manual

User’s Guide  
16-Bit Ethernet PC Card  
Ethernet PC Card  
What’s Inside  
Hardware Description 2  
LED Indicators 2  
Pages 2 to 5  
see this side  
Hardware Installation 3  
Software Driver Installation 4  
EMI Certification 5  
í
Pages 6 to 8  
see this side  
Specifications 7  
Software Drivers 7  
Technical Support 8  
î
Hardware Installation  
1. Insert the Ethernet PC Card into the computer’s PCMCIA  
slot. Insert the card with the 68-pin connector facing the  
PCMCIA slot and the label facing up. See Figure 1 for  
illustration.  
Figure 1. Inserting the Ethernet PC Card into the Type II  
PCMCIA Slot.  
2. Plug the media coupler into the card’s 15-pin connector.  
3. Connect the media coupler to the network using either UTP  
or thin coax cabling.  
a. Connecting to the RJ-45 port using UTP cable.  
Figure 2. Connection Using UTP Cable  
(EtherPair-PCMCIA, model EN2216-1)  
3
b. Connecting to the BNC port with thin coax cable.  
Figure 3. Connecting to Thin Ethernet Cable  
(EtherDuo-PCMCIA, model EN2216-2)  
Note: If the card is attached to the end of the network segment,  
be sure a 50-Ohm terminator is installed on the open end of the  
T-type connector.  
Software Driver Installation  
The diskette labled “Driver Diskette,” that comes with the  
package contains all the software drivers available for the  
Ethernet PC Card. A RELEASE.TXT file, describing the  
contents of the diskette is found in the root directory. Different  
drivers are stored in separate subdirectories, which also  
include a text file. Select the driver you need for your system  
and refer to the text file for the installation procedure.  
4
EMI Certification  
FCC Class B Certification  
Accton Technology Corporation  
Model Number: EN2216  
FCC ID: HEDEN2216  
This device complies with Part 15 of the FCC Rules. Operation is  
subject to the following conditions:  
1. This device may not cause harmful interference, and  
2. This device must accept any interference received, including  
interference that may cause undesired operation.  
Warning! This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment  
generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee  
that interference will not occur in a particular installation. If this equipment  
does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the  
following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the distance between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from  
the one which the receiver is connected to.  
• Consult the dealer or an experienced radio/TV technician for  
help.  
You may use unshielded twisted-pair (UTP) cable for RJ-45  
connections.  
You are hereby cautioned that changes or modifications not  
expressly approved by the party responsible for compliance could  
void your authority to operate the equipment.  
The user may find the following booklet prepared by the Federal  
Communications Commission helpful:  
5
The Interference Handbook  
This booklet is available from the U.S. Government Printing  
Office. Washington, D.C. 20402. Stock No. 004-000-00345-4.  
Note: In order to maintain compliance with the limits of a Class B  
digital device, Accton requires that you use a quality interface cable  
when connecting to this device. Changes or modifications not  
expressly approved by Accton could void the user's authority to  
operate this equipment. Suggested cable type is unshielded twisted-  
pair (UTP) for RJ-45 connections and thin coax cable for BNC  
connections.  
VCCI Class B Compliance  
This product also complies with CISPR22 Class B.  
EN55022 Declaration of Conformance  
This is to certify that the Accton Ethernet Adapter is shielded  
against the generation of radio interference in accordance with  
the application of Council Directive 89/336/EEC, Article 4a.  
Conformity is declared by the application of EN55022:1987  
Class B (CISPR 22:1985/BS 6527:1988).  
6
Specifications  
Standard Conformance  
EN2216-1: IEEE 802.3 (10BASE-T)  
EN2216-2: IEEE802.3 (10BASE-T,  
10BASE2)  
PCMCIA Release 2.1 Type II  
PCMCIA-compliant computers  
10 Mbps (20 Mbps at full duplex)  
EN2216-1: 1 RJ-45 port (10BASE-T)  
EN2216-2: 1 RJ-45 port (10BASE-T)  
1 BNC port (10BASE2)  
Host Interface  
Ethernet Data Rate  
Media Connection  
Data Bus Width  
RAM Buffer  
16-bit  
32KB  
I/O Base Address  
Interrupt  
LED Indicators  
Power Requirement  
200H to 360H, software selectable  
2 (9), 3, 4, 5, 10, 11, 12, 15  
Transmit/Receive, Link  
RJ-45: +5V/130mA max.  
BNC: +5V/280mA max.  
0 to 55°C/32 to 131°F (Std. Operating)  
10% to 90% (Noncondensing)  
86 x 54 x 5 mm (3.38 x 2.12 x 0.2 in)  
FCC Class B, VCCI Class B,  
CISPR 22 Class B, CE Mark  
IEC1000-4-2/3/4  
Temperature  
Humidity  
Dimensions  
EMI Certification  
Immunity  
Environment  
Safety  
IEC-68, IEC-721  
UL, CSA, TÜV/GS  
Software Drivers  
NetWare ODI Drivers  
Novell NetWare 3.x, 4.x, NetWare LAN WorkPlace TCP/IP, Novell  
LAN Analyzer for NetWare  
NDIS Drivers  
Windows NT, Windows 95, MicroSoft LAN Manager, Windows  
for Workgroups, IBM LAN Server 2.x, IBM LAN Support V1.2,  
IBM OS/2 EE V2.0, DEC Pathworks V4.x, SUN PC-NFS, IBM  
TCP/IP for DOS & OS/2  
Packet Drivers  
FTP PC/TCP, NCSA TCP/IP  
Unix Drivers  
SCO Unix  
7
Technical Support  
Your dealer or installer is the person who understands your  
network and Accton units. If neither is available to help you,  
Accton technical support engineers are available by fax, mail  
or phone.  
Send your technical questions by fax to:  
International Headquarters: 886-3-577-0267  
USA Headquarters: 408-452-8988  
To obtain software upgrades connect via ftp to  
ftp.accton.com.tw  
International site  
US site  
Australia site  
Great Britain site  
Norway site  
Send your technical questions by email to  
Mail your technical questions to:  
International Headquarters  
Accton Technology Corporation  
Attn: Technical Support  
No. 1 Creation Road III  
Science-based Industrial Park  
Hsinchu 300, Taiwan, R.O.C.  
USA Headquarters  
Accton Technology Corporation  
Attn: Technical Support  
1962 Zanker Road,  
San Jose, CA 95112, U.S.A.  
8
During local business hours, call:  
International Headquarters  
Monday through Friday  
8 a.m. to 6 p.m.:  
886-3-5770-270  
USA Headquarters  
Monday through Friday  
7 a.m. to 5 p.m. Pacific Time:  
408-452-8900 or 800-926-9288  
The publisher assumes no responsibility for errors that may  
appear in this document. Nor does it make any commitment to  
update the information it contains.  
All brand and product names mentioned are trademarks or  
registered trademarks of their respective companies.  
EN2216  
E0198-R01  
150192-101  
9

Frigidaire 318200633 User Manual
Extron electronic Extron Electronics DVD Recorder VN MATRIX 325 User Manual
EPoX Computer EP 3VCA2 User Manual
Dell Computer Monitor P1913S User Manual
Black Box Computer Hardware LEH1008A User Manual
Atlantis Land WEBRUNNER PCI A01 PP3R User Manual
Asus P4S800 MX SE User Manual
Asus Motherboard P5LD2 VM DH User Manual
AOpen AW540 Series User Manual
Acnodes RMS 8190 User Manual